A/C NOT RELEASING

Hi,

Procedure with the open window is the same for both airbus versions.
You just need to be careful when selecting which version of the Airbus you own.

Extended, old version or the new version.

Cheers,

J-P

Hi J-P,
Sorry, but I am running into the following problem now:
I can NOT load a flight from the Display Unit. I checked the SimConnect and it reports it's working properly. When I try to load an approach the yellow distance rectangle just flashes, but nothing loads in the simulator; see screenshot of the Display Unit:
https://www.flickr.com/photos/141330124@N05/shares/d6mdsV
I thaught it worked before?
Thanks again

Hi J-P,
I was under the incorrect impression that the yellow & blue shield on a desktop icon meant that it is running as Administrator. I was wrong!!! After checking FSX and some other addons, I found that the box for "Run as Administrator" was NOT clicked.
So, after correcting this, FSiPanel works again. I performed 2 approaches (one from the server and another from the display unit) and both worked fine.
So thanks a lot for your help and my apologize for my mistake.

Hi J-P,
I uninstalled and re-installed FSiPanel.
When I tested it with an approach the same dark cockpit occurred. I did the troubleshooting and received this reply (see screenshot). I know I have a paid version of FSUIPC. What is with the "Admin Rights" of FSX?
Thanks for continued help

Hi J-P,
After deleting the file the same result as before.
One thing I noticed:
I shut down the simulator, than tried to shut down FSiPanel server, but neither Open or Exit would respond after right clicking on the FSi icon (it's like locked up!). I needed to bring up the task manager to shut down FSiPanel. The display unit shut down properly.
Thanks for help

Hi J-P,
I had to re-install FSX-SE some time ago and believe that after that everything worked well, with the exception of the PMDG reloads.
I don't recall making any changes.
Q: Is the mentioned config.txt located in c:\?
Is this the file?:

RunMode=SERVER
Version=1.0.0.84
FSUIPC=4.962a
FSUIPCRegistered=True
FSVers=FSX
PathFSX=C:\Program Files (x86)\Steam\steamapps\common\FSX
PathP3D=
PathFSXDocsMS=C:\Users\Juergen\Documents\Flight Simulator X - Steam Edition Files
PathFSXDocs=C:\Users\Juergen\Documents\Flight Simulator X - Steam Edition Files
PathPMDG737=C:\Program Files (x86)\Steam\steamapps\common\FSX\PMDG\PMDG 737 NGX\PanelState
PathPMDG747Q2=C:\Program Files (x86)\Steam\steamapps\common\FSX\PMDG\PMDG 747 QOTS II\PanelState
PathPMDG777=C:\Program Files (x86)\Steam\steamapps\common\FSX\PMDG\PMDG 777X\PanelState
PathPMDG747=
PathPMDGMD11=
PathAES320=C:\Users\Juergen\Documents\Aerosoft\AerosoftAirbusExtended
PMDGFlightPlanFolder=C:\Program Files (x86)\Steam\steamapps\common\FSX\PMDG\FLIGHTPLANS
LVLDFlightPlanFolder=C:\Program Files (x86)\Steam\steamapps\common\FSX\Level-D Simulations\navdata\Flightplans
LUAPointKeycode=190
FSXCrashMode=2
FSXCrashXTimes=4
iFlyAutoBrake=1
AESWindowName=Open
ForceQNHSTD=0
ServerPort=22490
FSXActiveSky=0

Thanks

Hi J-P,
Did as requested:
All NORMAL. Loads the aircraft for about 2sec with dark instruments and than changes to the save state -all gauges and indicators normal as well as engines running.
Seems to be normal.
Thanks

Hi J-P,
I tried a different livery of the PMDG B737, however same problem.
I tried a PMDG B777 also the same problem - dark instruments, no indicators and FSi Panel will not finish trimming the aircraft.
Thanks for help

Hi,

I just gave it a try and it worked normally.
Are you using ActiveSky? was it running with a valid metar at the airport you wanted to fly?

Hi J-P,
Yes and it's version 1.20.8465 which is the latest

Hi J-P,
I assume it's V1 (checks at start up 1.0.0.84)
Did NOT load 737 over 737.
I start FSX-SE with default a/c (trike) in ????Harbor and make selection in FSi Panel.
Hope that helps

Hi,
I now have a strange problem,
I am running FSi Panel in a Server/Display unit config. The follow occurs when I move the aircraft to a selected approach:
Scenery loads and A/C (PMDG B737) loads and initializes (all instruments normal)
Then scenery reload appears and the aircraft is displayed with all blank instruments and lights
also the HUD extends, but no display
The green info strip shows: My Control, trimming your aircraft properly, please wait......
It never finishes trimming
Thanks for help