Print Page | Close Window

Enable EZCA Pro v3 Advanced Mode

Printed From:
Category: Flight One Partner Forums
Forum Name: EZdok Software
Forum Description: EZdok Forum for EZdok Camera
Printed Date: January-18-2021 at 9:36pm
Software Version: Web Wiz Forums 12.01 -

Topic: Enable EZCA Pro v3 Advanced Mode
Posted By: Steve Halpern
Subject: Enable EZCA Pro v3 Advanced Mode
Date Posted: February-12-2019 at 5:55pm

This is for ADVANCED users only as documentation is being worked on for its use. It cannot be fully supported until the documentation is complete.

So if you are and advanced user and want to dive into it, see below!

Important! The changes below are case sensitive. Write it exactly has presented.

To activate advanced mode just add the string MAGIC WIZARD=true to general.ini that is in the DB3 folder (leave other settings in place...).




Restart EZdok. This will show slider Advanced-Simple in the main window of effect processor.

To enable EXTm - it can be enabled via the general settings page, or write string EZCA TURBULENCE=true to section [GENERAL_SETTINGS]



Again, observe lowercase and uppercase letters. The algorithm is case sensitive!!!!!!


Posted By: jackson
Date Posted: July-03-2020 at 12:59pm
Is there a user manual available for the various options in the advanced mode ? I remember a post somewhere in the forums advising it was works in progress, but I haven' t seen anything further on this since then, unless I am missing something.
Thank you and congratulations for this excellent product...!


(Win10-64b, I7-2600k @4.8 Ghz, ASUS P8P67 Deluxe, EVGA GTX1080, 8Gb DDR3 G.Skill Ripjaws X 2133CL9)

Posted By: Nickbe
Date Posted: July-04-2020 at 1:18am

Unfortunately, I don't have time to finish the manual of the Advanced effects editor Studio.
A brief description of the most important part - setting up turbulence, I will leave here.

Over time, I will add a description of individual blocks here.


XTM - turbulence module.


The XTM turbulence module is configured in the advanced editor in the SHAKES section.

The General oscillation levels from the turbulence generators are set by sliders along the X Y Z P B H axes - these are the X,Y, Z, Pitch, Bank and Head axes.

IGR (INITIAL GENERATOR RATE) - sets the initial base frequency of all generators - small value - low oscillation frequency and Vice versa - high value - high oscillation frequency. This parameter (IGR) corresponds to the "TONE" slider in the Simple effects editor.

To adjust the oscillation pattern for different turbulence levels, you can directly select the turbulence type (DIRECT SOURCE SELECTION) in the next box of the advanced editor.

I describe the parameters to configure.

GAIN - the level of the turbulence effect of the selected type.

SHARP - the nature of the oscillations (higher value - more high-frequency bursts). 

SHEAR - depth of the turbulence effect shift (higher value - longer turbulence effect). 

The next two parameters are a kind of randomness generator of the turbulence effect (FX RANDOMIZER) with two parameters -

D-RING - dynamic range of the effect and R_INT - randomizer intervals.

These parameters make it possible to achieve a realistic character of turbulence. 

T-TIME is a Transition time-the delay time when switching from one type of turbulence to another.

Lower box "SPEED FACTOR" - adjusts the dependence of all the effects of turbulence on the speed characteristics of the aircraft.


Additional information about the Advanced effects editor.

Basic diagram of relationships within the effects processor." rel="nofollow">AFX.jpg


Designations of the axes of the aircraft inside the simulator.


Nick B.
Ezdok Software

Posted By: jackson
Date Posted: July-06-2020 at 10:46am
Thank you very much for your answer..!



(Win10-64b, I7-2600k @4.8 Ghz, ASUS P8P67 Deluxe, EVGA GTX1080, 8Gb DDR3 G.Skill Ripjaws X 2133CL9)

Print Page | Close Window

Forum Software by Web Wiz Forums® version 12.01 -
Copyright ©2001-2018 Web Wiz Ltd. -