SimForums.com Homepage
Forum Home Forum Home > Flight One Partner Forums > Opus Software
  New Posts New Posts RSS Feed - Opus PDK Interface Setup Guide
  FAQ FAQ  Forum Search   Register Register  Login Login

Opus PDK Interface Setup Guide

 Post Reply Post Reply
Author
Message
mokeiko View Drop Down
Intermediate Group
Intermediate Group


Joined: February-12-2014
Points: 57
Post Options Post Options   Thanks (0) Thanks(0)   Quote mokeiko Quote  Post ReplyReply Direct Link To This Post Topic: Opus PDK Interface Setup Guide
    Posted: December-07-2017 at 1:00am
How do I setup PDK for V4? The instructions goes up to v3.


Also how do I do the following, I dont know how

"You should use FSISERVER.exe with the P3D or P3D34 argument."

thanks for any help

Fly safe
Back to Top
Opus Software View Drop Down
Senior Member
Senior Member


Joined: April-12-2012
Location: Grantham, UK
Points: 13121
Post Options Post Options   Thanks (0) Thanks(0)   Quote Opus Software Quote  Post ReplyReply Direct Link To This Post Posted: December-07-2017 at 2:18am
There is no PDK for P3Dv4 and you must run FSISERVER with the P3D4 argument.

Stephen
Back to Top
mokeiko View Drop Down
Intermediate Group
Intermediate Group


Joined: February-12-2014
Points: 57
Post Options Post Options   Thanks (0) Thanks(0)   Quote mokeiko Quote  Post ReplyReply Direct Link To This Post Posted: December-07-2017 at 12:13pm
FSISERVER with the P3D4 argument

what does this mean? how do you do this?

sorry I don't understand the jargon.

Fly safe
Back to Top
Opus Software View Drop Down
Senior Member
Senior Member


Joined: April-12-2012
Location: Grantham, UK
Points: 13121
Post Options Post Options   Thanks (0) Thanks(0)   Quote Opus Software Quote  Post ReplyReply Direct Link To This Post Posted: December-07-2017 at 2:44pm
You start the software using the FSISERVER program specifying your sim type and version with the program argument.
For example, you run the software like this...

C:\OpusFSI_v5\FSISERVER.EXE P3D4

Create this as a shortcut on your desktop and run in Admin Mode and all will be ok.

Stephen :-)
Back to Top
mokeiko View Drop Down
Intermediate Group
Intermediate Group


Joined: February-12-2014
Points: 57
Post Options Post Options   Thanks (0) Thanks(0)   Quote mokeiko Quote  Post ReplyReply Direct Link To This Post Posted: December-07-2017 at 3:12pm
I see this in my folder: FSISERVER.EXE

do I rename this to FSISERVER.EXE P3D4 and then make a shortcut?

The reason I'm asking about this is because of another thread about creating panning sequences are not working for me and maybe it has to do with this problem i'm having now, but I doubt that now.

Fly safe
Back to Top
Opus Software View Drop Down
Senior Member
Senior Member


Joined: April-12-2012
Location: Grantham, UK
Points: 13121
Post Options Post Options   Thanks (0) Thanks(0)   Quote Opus Software Quote  Post ReplyReply Direct Link To This Post Posted: December-07-2017 at 3:43pm
No. You run the FSISERVER.exe program and pass the P3D4 phrase as an argument to the program.

See the Getting Started Guide. The program is Started and the P3D4 phrase is included as a Command Line Argument.

Stephen
Back to Top
 Post Reply Post Reply
  Share Topic   

Forum Jump Forum Permissions View Drop Down

Forum Software by Web Wiz Forums® version 11.10
Copyright ©2001-2017 Web Wiz Ltd.

This page was generated in 0.094 seconds.